自动上料搅拌车的清洗要点你了解吗？
今天我们中科聚峰厂家的小编就来给您介绍自动上料搅拌车的保养注意事项，希望通过我们的介绍让您对自动上料搅拌车的保养注意事项等问题有更深入的了解
Today, our small editor from Zhongke Jufeng factory will introduce the maintenance precautions of the automatic feeding mixer to you. I hope that through our introduction, you can have a deeper understanding of the maintenance precautions of the automatic feeding mixer
1、在施工现场卸料完毕后，应立即用搅拌车随带的软管冲洗进料斗、出料斗、卸料溜槽等处，清除粘附在车身各处的污泥及混凝土。在返回搅拌站的途中，应向搅拌筒内注150---200L水以清洗筒壁及叶片粘结的混凝土残渣。
1. After unloading at the construction site, the inlet hopper, discharge hopper and discharge chute should be flushed with the hose attached to the mixer to remove the sludge and concrete adhering to the vehicle body. On the way back to the mixing station, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded by the cylinder wall and blades.
2、每天工作结束后，司机应负责向搅拌筒内注入清水并高速(14—18转/分)旋转5—10分钟，然后将水排去，以保证筒内清洁。用高压水清洗搅拌筒各个部分时，应注意避开仪表及操纵杆等部位。压力水喷嘴与车身油漆表面间的距离不得小于40厘米。
2. At the end of each day's work, the driver should inject fresh water into the mixing drum and rotate it at high speed (14-18 RPM) for 5-10 minutes, and then drain the water to ensure the cleanness of the drum. When cleaning each part of the mixing drum with high pressure water, pay attention to avoid the instrument and control rod. The distance between the pressure water nozzle and the paint surface of the vehicle body shall not be less than 40 cm.
3、清除搅拌筒内外积污及残存的混凝土渣块时，以及在机修人员进入筒内进行检修和焊补作业时，需先关闭汽车发动机，使搅拌筒完全停止转动。在机修人员进入筒内工作期间，必须保证拌筒内通风良好，空气新鲜，无可然气体及有害灰尘，氧气供应充足。在筒内使用电动工具操作时，操作人员必须有良好的绝缘保护。
3. When removing the dirt inside and outside the mixing drum and the remaining concrete slag, and when the machine maintenance personnel enter the cylinder for maintenance and welding repair, it is necessary to turn off the automobile engine to stop the mixing drum completely. During the period when the machine maintenance personnel enter the cylinder, they must ensure that the mixing drum is well ventilated, the air is fresh, there is no natural gas and harmful dust, and the oxygen supply is sufficient. When using electric tools in the cylinder, the operator must have good insulation protection.
4、工作时，不得将手伸入旋转的搅拌筒内，严禁将手伸入主卸料溜槽和加长卸料溜槽的连接部位自动，自动上交搅拌车在工作时应注意什么以免发生事故。
4. When working, do not put your hand into the rotating mixing drum. It is strictly forbidden to put your hand into the connection between the main discharge chute and the lengthened discharge chute. It will automatically hand over to the mixer truck what should be paid attention to when working to avoid accidents.
以上是关于自动上料搅拌车的清洗要点的相关内容介绍，希望对大家有所帮助，想要了解更多内容欢迎点击中科聚峰厂家www.jfjiaobanche.com官网。
The above is about the automatic feeding mixer cleaning points related content introduction, hope to help you, want to know more content, welcome to click Zhongke Jufeng manufacturers www.jfjiaobanche.com Official website.
