避免自上料搅拌车轮胎的过度损害具体做法
随着搅拌车成本的持续提升，逼迫着人们不放过任何一个节省支出的细节。搅拌车轮胎其实是使用过程中颇占成本的一项耗材，尽量避免轮胎的过度损害就要先了解损害有怎样的表现，然后再来看处理方法。
With the continuous increase in the cost of mixer trucks, people are forced to spare no details of cost savings. In fact, the mixer tire is a consumable that accounts for a lot of costs in the use process. To avoid excessive damage to the tire as far as possible, we should first understand the performance of the damage, and then look at the treatment methods.
转向轮轮胎胎面或两边不正常磨损。检查胎压是否过低或轮胎质量是否过关。不要贪图便宜使用三无轮胎。轮胎的钢圈是否失圆，做个动平衡。检查前束尺寸、转向拉杆球头是否松旷，方向机固定螺丝有没有松动。转向桥主轴或压力轴承是否磨损严重变形或损坏。
Abnormal wear on the tread or both sides of the steering wheel tire. Check whether the tire pressure is too low or whether the tire quality is qualified. Don't use three no tires for cheap. Whether the steel ring of the tire is out of round, make a dynamic balance. Check the toe in size, whether the steering rod ball joint is loose, and whether the steering gear fixing screw is loose. Whether the steering axle main shaft or pressure bearing is worn, severely deformed or damaged.
后轮轮胎胎面呈不规则型磨损。检查钢圈，轮毂螺丝及轴头螺丝是否松动。检查刹车毂是否失圆。弹簧板和弓卡固定螺丝是否有松动。日常勤检查轮胎气压，要看看轮胎胎面的磨损情况。早发现早修理，把损失降到低限度。
The tread of the rear tires is worn irregularly. Check whether the steel ring, hub screw and shaft head screw are loose. Check whether the brake hub is out of round. Check whether the fixing screws of spring plate and bow clamp are loose. Check the tire pressure frequently every day to see the wear of the tire tread. Find and repair early, and reduce the loss to a minimum.
轮胎部分的早期磨损。适当提高轮胎充气量，可以减小轮胎与路面的接触面积，从而减小轮胎的滚动阻力，节约燃油。但充气量过大时，不但影响轮胎的减振性能，还会使轮胎变形量过大，与地面的接触面积太小，磨损只能由胎面部分承担，形成早期磨损。
Early wear of the central part of the tire. Properly increasing the inflation of the tire can reduce the contact area between the tire and the road, so as to reduce the rolling resistance of the tire and save fuel. However, when the inflation volume is too large, it will not only affect the vibration damping performance of the tire, but also make the tire deformation too large, and the contact area with the ground is too small. The wear can only be borne by the central part of the tread, forming early wear.
此外自上料搅拌车厂家提醒各位司机应避免原地打方向，而应该在轮胎滚动时打方向，这样的话，地面给搅拌车轮胎带来的才是全方位且均匀的正常磨损。由于车感不佳，很多新手都喜欢原地打方向，这个坏习惯基本上是从驾校里面带出来的。原地打方向会令轮胎的磨损集中在同一个接触面上，造成轮胎局部严重磨损，缩短使用寿命。
In addition, since the charging mixer truck manufacturer reminds all drivers to avoid turning the direction in situ, and should turn the direction when the tire rolls. In this way, the ground will bring all-round and uniform normal wear to the mixer truck tire. Due to the poor feeling of the car, many novices like to steer in place. This bad habit is basically brought out from the driving school. Turning the direction in place will make the wear of the tire concentrated on the same contact surface, causing serious local wear of the tire and shortening the service life.
以上就是问题解答的相关内容了，希望能够帮助到大家，如对这一问题还存在任何疑问，都欢迎关注我们网站https://www.jfjiaobanche.com并咨询我们的工作人员，将竭诚为您服务。
The above is the relevant content of the question answer. I hope it can help you. If you still have any questions about this problem, you are welcome to follow our website https://www.jfjiaobanche.com And consult our staff, will serve you wholeheartedly.
