混凝土自上料搅拌车行车与保养两不误
混凝土自上料搅拌车是现在工程建设不可或缺的工程车辆，特殊的工作环境造就了不一样的它，下面随混凝土自上料搅拌车厂家一起来看看搅拌车的保养。
The concrete self loading mixer is an indispensable engineering vehicle for engineering construction. The special working environment has created a different one. Now let's join the manufacturer of the concrete self loading mixer to check the maintenance of the mixer.
1、初次工作50小时紧固前台U型螺栓、前台与减速机底座连接螺栓、减速机法兰与搅拌筒连接螺栓、托轮与机架的紧固螺栓及托轮锁紧螺母；以后每月定期检查一次。
1. Tighten the U-shaped bolts of the front desk, the connecting bolts between the front desk and the reducer base, the connecting bolts between the reducer flange and the mixing drum, the fastening bolts between the supporting wheel and the frame and the locking nuts of the supporting wheel after the first 50 hours of work; After that, it shall be checked regularly every month.
2、各紧固螺栓在出厂前都经过严格检验，均达到要求的紧固力矩，对于因使用而发生的松动，要及时紧固，恢复其规定力矩，严重损坏的要及时更换。
2. All fastening bolts shall be strictly inspected before delivery and meet the required tightening torque. Looseness due to use shall be tightened in time to restore the specified torque, and those seriously damaged shall be replaced in time.
3、每次在车辆发动之前，检查液压油冷却器和减速机的油位，保证油位指示在目视范围内；液压系统应经常保持清洁和密封，以免尘粒和水份等污染系统液压油，造成系统不能正常工作或损坏。
3. Before starting the vehicle each time, check the oil level of the hydraulic oil cooler and reducer to ensure that the oil level indication is within the visual range; The hydraulic system should always be kept clean and sealed to prevent dust particles and moisture from polluting the hydraulic oil of the system, causing the system to fail to work normally or be damaged.
4、每天行车前检查托轮与滚道的结合面润滑油是否干涩，应及时补充，保持良好的润滑效果。
4. Before driving every day, check whether the lubricating oil on the joint surface of the supporting wheel and the raceway is dry, and replenish it in time to maintain a good lubricating effect.
5、至少每月打开一次托轮护罩，清理里面的污物；通过托轮上的油嘴，向托轮内注入润滑油脂。
5. Open the supporting wheel shield at least once a month to clean the dirt inside; Inject lubricating grease into the supporting roller through the oil nozzle on the supporting roller.
6、保证传动轴至少每月润滑一次。
6. Ensure that the transmission shaft is lubricated at least once a month.
7、经常性检查管路及液压设备的紧固螺栓是否有松动，保障设备的安全，必要时更换螺栓。
7. Regularly check whether the fastening bolts of the pipeline and hydraulic equipment are loose to ensure the safety of the equipment. Replace the bolts if necessary.
8、注意观察散热器上的真空表指示，当指针位于红色区域时，应及时更换滤芯，对于使用一年以上的滤芯，即使指针不在红色区域，也应该更换；要使用同一生产厂家的产品。
8. Observe the indication of the vacuum gauge on the radiator. When the pointer is in the red area, replace the filter element in time. For the filter element that has been used for more than one year, replace it even if the pointer is not in the red area; Use products from the same manufacturer.
9、至少每隔6个月检查液压泵、液压马达及油路的密封性能。
9. Check the sealing performance of hydraulic pump, hydraulic motor and oil circuit at least every 6 months.
10、及时检查散热器的风扇和温控开关的性能，保证其正常工作,油温一般在60℃左右时风扇会自动打开。
10. Timely check the performance of the radiator fan and temperature control switch to ensure their normal operation. Generally, when the oil temperature is about 60 ℃, the fan will turn on automatically.
所以说搅拌车司机不仅要会开搅拌车还要会“养”它，以上十点就是为您推荐的相关问题内容了，您可以作为参考使用，更多相关信息就来我们网站https://www.jfjiaobanche.com咨询了解吧！
So the mixer driver should not only be able to drive the mixer but also be able to "maintain" it. The above ten points are recommended for you. You can use them as reference, and more relevant information will come to our website https://www.jfjiaobanche.com Ask and understand!
下一篇：全自动搅拌车具备三种性能优势上一篇：选择自上料搅拌车需要考虑重量吗？
