自上料搅拌机的刹车系统和料门有哪些需要注意的呢？
自上料搅拌机在日常使用中制动系统和刹车系统相对来说很重要，直接对接着自身，所以说这点很重要，需要好好了解下刹车系统如何？
Since the charging mixer in daily use, the brake system and brake system are relatively important, directly for their own safety, so this is very important, we need to have a good understanding of the braking system?
断气刹制动气室内有个强力绷簧，行车时压缩空气将绷簧顶起。手刹车就是把气放掉，让绷簧把刹车锁死。行车中气压过低时也会发生刹车效应，保证。惯例刹车是手刹锁住传动轴，脚瞬时由压缩空气进入制动气室锁住车轮。在手刹或传动轴机械毛病时，手刹失灵;在气泵、管路、储气筒、制动阀任何一个部位毛病时，脚刹失灵。而断气刹车就可有用避免这些风险。
There is a strong tension spring in the brake air chamber of the air cut brake, which is jacked up by compressed air when driving. The handbrake is to let the air out and let the tension spring lock the brake. When the air pressure is too low, the braking effect will occur to ensure safety. The conventional brake is that the hand brake locks the transmission shaft, and the foot enters the brake chamber by compressed air instantaneously to lock the wheels. In case of mechanical failure of hand brake or transmission shaft, the hand brake fails; when any part of air pump, pipeline, air reservoir and brake valve fails, the foot brake fails. The air brake can be useful to avoid these risks.
由于旅行开关未能修理或更换。绞车过热主要是由于制动装置间隙不当造成的。 会造成什么后果，今天就简单来了解下中科自上料搅拌机的配料门吧：
The travel switch could not be repaired or replaced. The overheating of winch is mainly caused by improper clearance of brake device. What are the consequences? Let's learn about the mixing gate of the charging mixer
配料机的进料门工作不正常。 主要原因是门和门框之间的间隙太大或门变形。 门被沙子和砾石挡住了。 纠正材料门或更换材料门或橡胶板。 搅拌车气缸力小，需要检查气源压力或修缸。料斗偏向或卡住。 这主要是由于两个凸起的芯或芯的跳线长度不一致。可以通过调节灯芯的长度，调节灵敏度的下限和调节防跳装置来。卸下料斗后，无法控制跌落。
The feeding door of the batching machine is not working properly. The main reason is that the gap between the door and the door frame is too large or the door is deformed. The door was blocked by sand and gravel. Correct material door or replace material door or rubber plate. The cylinder force of the mixer is small, so it is necessary to check the air source pressure or repair the cylinder. The hopper is deflected or jammed. This is mainly due to the inconsistency of the jumper length of two protruding cores or cores. It can be solved by adjusting the length of the wick, adjusting the lower limit of sensitivity and adjusting the anti bounce device. After unloading the hopper, the drop cannot be controlled.
以上还是敢于自上料搅拌机刹车方式和料门出现问题的方法的相关介绍，希望对你们有所帮助，想要了解更多内容欢迎点击https://www.jfjiaobanche.com中科自上料搅拌机官网。
The above or dare from the charging mixer brake mode and material door problems related to the introduction, hope to help you, want to learn more content, welcome to click https://www.jfjiaobanche.com Zhongke from the official website of charging mixer.
下一篇：中科自上料搅拌机的操作优势有哪些？上一篇：混凝土搅拌车卸料的注意事项！
