搅拌车轮圈和轮胎的组合事项
全自动搅拌车在使用和购买的过程中都要看重，注重率生产、生产一直各大企业比较重视的问题，选择优良产品注重施工效率的提高，轮胎是一个其作用的部件。下面来讲讲搅拌车轮圈和轮胎的组合事项吧。
In the process of using and purchasing the fully automatic mixer truck, we should pay attention to the production rate and energy-saving production, which have always been paid more attention by major enterprises. We should choose excellent products and pay attention to the improvement of construction efficiency. Tire is a part of its function. Now let's talk about the combination of mixer rim and tire.
请使用标准搅拌车轮圈，已经变形或这损伤的搅拌车轮圈切勿使用。搅拌车轮圈与搅拌车轮胎组合前，要先清理轮圈和搅拌车轮胎，不可以有杂物留在内部。
Please use the standard mixer wheel. Do not use the deformed or damaged mixer wheel. Before mixing wheel rim and mixing tire are combined, the wheel rim and mixing tire shall be cleaned first, and no sundries shall be left inside.
搅拌车轮圈与搅拌车轮胎组合之前。可以使用橡润滑剂或着肥皂水擦拭胎唇轮圈凸缘，一定不要使用油性润滑剂。轮圈与搅拌车轮胎组合时应注意嵌合情形，不要使用超过正常范围之风压强行安装，以免发生危险。
Before the combination of mixer wheel rim and mixer tire. Rubber lubricant or soapy water can be used to wipe the tire lip and rim flange, and oily lubricant must not be used. When the rim is combined with the tire of the mixer truck, attention shall be paid to the fitting situation. Do not use the wind pressure exceeding the normal range to force the installation, so as to avoid danger.
轮圈与搅拌车轮胎组合需要由搅拌车轮胎行专门人员来操作，请勿自行组合。
The combination of wheel rim and mixer tire needs to be operated by special personnel of mixer tire line. Do not combine by yourself.
假如搅拌车轮胎运用日久，外胎锈死在轮圈内而不容易取下时，能够将轮胎平放在洁净的空中上，用撬棒在胎口与轮圈之间撬开一定间隙，在轮圈与外胎的分离部倒些肥皂水或清水，并用铁锤沿l轮圈外侧稍加锤击，使水在振动的过程中从缝隙处渗入生锈面，待浸透后外胎便容易拆下来。
If the mixer tire is used for a long time and the outer tire is rusted in the rim and is not easy to remove, the tire can be placed flat in the clean air, pry a certain gap between the tire mouth and the rim with a crowbar, pour some soapy water or clean water into the separation part between the rim and the outer tire, and hammer slightly along the outside of the L rim with a hammer to make the water penetrate into the rusty surface from the gap in the process of vibration, and the outer tire can be easily removed after being soaked.
此外轮胎气压应按使用说明书的要求合理充气，即同一轴上的两个轮胎气压必须相同；当轮胎出现异常磨损时，应立即查明原因。定位失准和转向机构技术故障是异常磨损的主要原因。车轮动平衡不良、超载等因素也是轮胎异常磨损的原因。
In addition, the tire pressure shall be inflated reasonably according to the requirements of the operation manual, that is, the pressure of two tires on the same axle must be the same; In case of abnormal tire wear, find out the cause immediately. Misalignment of positioning and technical failure of steering mechanism are the main causes of abnormal wear. Poor wheel dynamic balance, overload and other factors are also the reasons for abnormal tire wear.
全自动搅拌车厂家提醒您，可以通过观察轮胎花纹深度，正常磨损到极限的轮胎也要及时更换和更换。如果车辆在一般道路上行驶，轮胎花纹深度小于1.6mm，在高速公路上行驶时，轮胎花纹深度小于2.4mm。这是轮胎更换的表现；轮胎更换应配对；胎纹中的杂物要及时。
The manufacturer of full-automatic mixer truck reminds you that you can change and replace the tires that are normally worn to the limit in time by observing the tread depth of the tires. If the vehicle runs on ordinary roads, the depth of tire tread is less than 1.6mm, and when driving on highways, the depth of tire tread is less than 2.4mm. This is the performance of tire replacement; Tire replacement shall be matched; The sundries in the tread shall be removed in time.
搅拌车轮圈和轮胎的组合事项以及轮胎的其他事项就讲解完毕了，更多详细的要点或者细节问题就来关注我们的网站www.jfjiaobanche.com吧，让您获取到多多的有效的信息！
The combination of mixer wheel rim and tire and other matters of tire have been explained. For more detailed points or details, please pay attention to our website www.jfjiaobanche.com COM, let you get a lot of effective information!
下一篇：自上料搅拌车压力不足的方法上一篇：全自动搅拌车使用功能与进出料事项
