自上料搅拌车搅拌轴停止转动的原因
自上料搅拌车搅拌轴停止转动的原因是什么呢？实际上，在生产过程中当出现混凝土自上料搅拌车搅拌轴停止转动或是转动有点缓慢都是正常现象，如果这种情况先停机检查，看看有没有出现下列三种情况，下面自上料搅拌车厂家为您讲解：
What is the reason why the mixing shaft of the self feeding mixer truck stops rotating? In fact, it is normal for the mixing shaft of the concrete self loading mixer to stop rotating or rotate slowly during the production process. If this situation occurs, stop the machine first and check to see if the following three situations have occurred. Below, the manufacturer of the self loading mixer will explain to you:
1、电机传动皮带有没有出现松动的情况?自拌混凝土搅拌车电机传动皮带过松也能导致商品混凝土拌合机搅拌轴转动缓慢或者停止转动，电机传动皮带过松，导致传递的动力不足。
1. Is there any looseness in the motor drive belt? Loose motor drive belt of the self mixing concrete mixer can also cause the mixing shaft of the commercial concrete mixer to rotate slowly or stop rotating. Loose motor drive belt can lead to insufficient power transmission.
2、有没有严重超载?自拌混凝土搅拌车搅拌轴如果超过正常工作负荷，会使搅拌轴转动缓慢，若负荷过大，就会导致搅拌轴停转或者是搅拌轴弯曲。
2. Is there a serious overload? If the mixing shaft of the self mixing concrete mixer exceeds the normal working load, it will cause the mixing shaft to rotate slowly. If the load is too large, it will cause the mixing shaft to stop rotating or bend.
3、搅拌叶片或侧叶片与筒体内壁间有没有大的异物?出现这种情况也会使混凝土自动上料搅拌车搅拌轴停止转动或转动缓慢。搅拌叶片或侧叶片与罐内壁间有较大的异物也会导致搅拌轴停转，之所以能卡存异物，就是由于搅拌叶片或侧叶片与罐内壁间隙过大造成的，尤其是石子。
3. Are there any large foreign objects between the mixing blades or side blades and the inner wall of the cylinder? This situation can also cause the mixing shaft of the automatic concrete loading mixer to stop rotating or rotate slowly. The presence of large foreign objects between the mixing blades or side blades and the inner wall of the tank can also cause the mixing shaft to stop rotating. The reason why foreign objects can be stuck is due to the large gap between the mixing blades or side blades and the inner wall of the tank, especially stones.
此外有关的保养事项也要多加注意，比如：
In addition, pay more attention to maintenance matters, such as:
调整气动自动开关的上限和下限。如果压力太低，气缸会减速，如果压力太高，气动系统的气密性会降低。
Adjust the upper and lower limits of the pneumatic automatic switch. If the pressure is too low, the cylinder will slow down, and if the pressure is too high, the airtightness of the pneumatic system will decrease.
使用自上料搅拌车检查油位，并确保油位在量油尺的顶线和底线之间。当油位接近下，添加新油。
Use a self loading mixer truck to check the oil level and ensure that it is between the top and bottom lines of the dipstick. When the oil level approaches the lower limit, add new oil.
确保皮带正确张紧。用手指推动皮带，使其松开约10毫米。更换传送带时，必须更换整个组以保持共同的张力。
Ensure that the belt is properly tensioned. Push the belt with your fingers to loosen it by approximately 10 millimeters. When replacing the conveyor belt, the entire group must be replaced to maintain a common tension.
由于气体系统中充满油，因此需要足够量的油才能正常运行。只有这样，才能同时使用独立式混合器的功率来延长气体系统的使用寿命。
Due to the gas system being filled with oil, a sufficient amount of oil is required for normal operation. Only in this way can the power of the independent mixer be used simultaneously to extend the service life of the gas system.
自上料搅拌车搅拌轴停止转动的原因就讲解到这里了，希望能够给您好的帮助，更多事项了解就来我们网站https://www.jfjiaobanche.com咨询吧！
That's all for explaining the reason why the mixing shaft of the self feeding mixer truck stopped rotating. I hope it can be helpful to you. For more information, please come to our website https://www.jfjiaobanche.com Consult!
下一篇：全自动搅拌车在修桥工程中的优势上一篇：使用自动上料搅拌车的几个要点
